Preview

Stand Equipment and Test Methods of Modern Optical Sights

https://doi.org/10.21122/2220-9506-2022-13-3-165-171

Abstract

Manufacture of sights with high output characteristics is a prerequisite for achieving the necessary accuracy when shooting. The aim of the work was to analyze the influence of pancratic optical sights’ main parameters on their output performance characteristics.

It is shown that in order to achieve the quality level of the world’s best samples, high image quality – no drop in contrast by no more than 30 % of the calculated value, careful manufacturing and control of both mechanical and optical parts, as well as components of the assembly units of products, the technological process of assembly and alignment is necessary.

Bench equipment and test methods which made it possible significantly increase the level of serial production are described, also some characteristics of GS3-12×50, GS3-24×56, GS5-25×56 “NTC “LEMT” BelOMO” are presented.

 

About the Authors

A. M. Kurganovich
LEMT Scientific and Technical Center
Belarus

Makayenka str., 23, Minsk 220114,



V. A. Stasilovich
LEMT Scientific and Technical Center
Belarus

Address for correspondence: 
Stasilovich V.A. - 
“STC LEMT  ” BelOMO ”, 
Makayenka str., 23, Minsk 220114, Belarus
e-mail: Stasilovich19@gmail.com



I. P. Shishkin
LEMT Scientific and Technical Center
Belarus

Makayenka str., 23, Minsk 220114,



A. P. Shkadarevich
LEMT Scientific and Technical Center
Belarus

Makayenka str., 23, Minsk 220114,



References

1. Darko D. Jankovic, Darko M.Vasiljevic, Ljubisa D. Tomic, Sedan J. Duvnjak. Modern sniper rifles in the armament of the Serbian armed Forces. Vojnotehnicki glaznik, 2019, vol. 67, no. 3, pp. 663–688. DOI: 10.5937/vojtehg67-18141

2. Filipov M.A. On the wagging of the muzzle velocity of a bullet on the accuracy of sniper rifle shooting. Proceedings of Tula State University. Technical Sciences, 2018, pp. 241–249 (in Russian).

3. Belsky A.B. Pankratic sniper sights of the new generation. Questions of Defense Technology, 2009, no. 9–10, series 16 (in Russian).

4. Kiselyov Al.S., Kiselyov An.S., Nazarov V.N. Investigation of the influence of errors in the assembly and alignment of optical sights on the result of shooting. Federal State Autonomous Educational Institution of Higher Education “St. Petersburg National Research University of Information Technologies, Mechanics and Optics”, 2006, pp. 150–155 (in Russian).

5. INFRAMET. OPO-Z test station. Manual. Tester of telescopic sight, Poland, 2018.

6. Sosnov A.N., Sosnova N.K., Kritinina S.V. Optical methods for error control of manufacturing precision cylindrical lenses. Interexpo Geo-Siberia Publ., 2008.

7. Bao Bui Dinh, Latyev S.M., Theska R. Automation of lenses centering at gluing in the frame. Scientific and Technical Bulletin of Information Technologies, Mechanics and Optics, 2015, vol. 15, no. 6, pp. 1030–1035 (in Russian). DOI: 10.17586/2226-1494-2015-15-6-1030-1035

8. Latyev S.M. Design of precision (optical) instruments. St. Petersburg: Polytechnic Publ., 2007, 580 p.

9. Latyev S.M., Bao Bui Dinh. Methods of lens centering in optical systems. News of higher educational institutions. Izvestiya Vysshikh Uchebnykh Zavedeniy. Priborostroenie [Instrumentation], 2013, vol. 56, no. 11, pp. 66–72 (in Russian).


Review

For citations:


Kurganovich A.M., Stasilovich V.A., Shishkin I.P., Shkadarevich A.P. Stand Equipment and Test Methods of Modern Optical Sights. Devices and Methods of Measurements. 2022;13(3):165-171. https://doi.org/10.21122/2220-9506-2022-13-3-165-171

Views: 449


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2220-9506 (Print)
ISSN 2414-0473 (Online)